Zynq UltraScale+ MPSoC ZCU102 Evaluation Kit

Description

Product Description The ZCU102 Evaluation Kit enables designers to jumpstart designs for automotive, industrial, video, and communications applications. This kit features a Zynq™ UltraScale+™ MPSoC with a quad-core Arm® Cortex®-A53, dual-core Cortex-R5F real-time processors, and a Mali™-400 MP2 graphics processing unit based on 16nm FinFET+ programmable logic fabric by AMD. The ZCU102 supports all major peripherals and interfaces, enabling development for a wide range of applications. Key Features & Benefits Optimized for quick application prototyping with Zynq UltraScale+ MPSoC DDR4 SODIMM – 4GB 64-bit w/ ECC attached to processing system (PS) DDR4 Component – 512MB 16-bit attached to programmable logic (PL) PCIe® Root Port Gen2 x4, USB3, Display Port, and SATA 4x SFP+ interfaces for Ethernet 2x FPGA Mezzanine Card (FMC) interfaces for I/O expansion, including 16 16.3Gb/s GTH transceivers and 64 user-defined differential I/O signals Featured AMD Devices Featuring the Zynq UltraScale+ XCZU9EG-2FFVB1156 MPSoC System Logic Cells (K) 600 Memory (Mb) 32.1 DSP Slices 2,520 Maximum I/0 Pins 328 PRODUCT INFORMATION Specifications Board Features Featuring the ZCU102 Evaluation Board Configuration Onboard JTAG configuration circuitry to enable configuration over USB Dual Quad-SPI flash memory Boot from SD card Memory PS 4GB DDR4 64-bit SODIMM w/ ECC PL 512MB DDR4 component memory ([256 Mb x 16] devices) at 1200MHz / 2400Mbps DDR 8KB IIC EEPROM Dual 64MB Quad SPI flash SD card slot Control & I/O 6x Directional Push Buttons (5x PL, 1x PS) DIP switches (8x PL) PMBUS & System Controller MSP430 for power, clocks, and I2C bus switching USB2/3 (MIO ULPI and 1 GTR)** Expansion Connectors 2x FMC-HPC connectors (16 GTH Transceivers, 64 differential user defined signals) 2x PMOD headers IIC Communication & Networking RGMII communications at 10, 100, or 1000 Mb/s. Serial GMII interface-supports a 1 Gb/s SGMII interface 4x SFP+ cage SMA GTH support (4x SMA Tx/Rx connectors) UART To USB bridge RJ45 Ethernet connector SATA (1 x GTR)** PCIe Gen2x4 Root Port** Display HDMI video input and output (3 GTH) External Retimer device driving an HDMI output connector 9x GPIO user LEDs (8x PL, 1x PS) VESA DisplayPort 1.2 source-only controller supports up to two lanes of main link data at rates of 1.62 Gb/s, 2.70 Gb/s, or 5.40 Gb/s. Clocking Programmable clocks System clocks, user clocks, jitter attenuated clocks 2x SMA MGT input clocks Power 12V wall adapter or ATX ** Switch enables either PCIe Root Port OR SATA, USB2/3 & DisplayPort What’s Inside ZCU102 Evaluation Board Access to a full seat of Vivado™ Design Suite: Design Edition Ethernet Cable Targus USB-3 USB3 Adapter USB Micro Cable Power Cords and Adapter Access to SDSoC Environment Documentation xtp426-zcu102-quickstart ug1182-zcu102-eval-bd

From the supplier's page.