Arduino Nano 33 BLE Sense with Headers – module ABX00035 (Original Made In ITALY)

Description

Description: Arduino Nano 33 BLE Sense with connectors The Arduino models in the Nano series are designed to extend the capabilities of small tiles to make their use possible in any project. Arduino Nano 33 BLE Sense is equipped with an energy-saving and efficient nRF52480 microcontroller capable of operating at 64 MHz . There is space for 1 MB of flash memory and 256 KB of RAM onboard. Additionally, the small board was equipped with a number of sensors, which gives a lot of possibilities. Thanks to this unit, the Nano 33 BLE Sense board is the most energy-efficient representative of the Nano family, despite its dimensions. The board supports Bluetooth 5.0 Low Energy standard Possibilities of Arduino Nano 33 BLE Sense Arduino Nano 33 BLE Sense is equipped with an a U-block NINA B306 module, managing Bluetooth communication in 5.0 LE standard. Onboard the Nano there is a 9-axis Inertial Measurement Unit (IMU) LSM9DS1 communicating via the I2C bus, which consists of a 3-axis gyroscope, accelerometer and magnetometer. Additionally, the small board is equipped with LPS22HB temperature and pressure sensor , HTS221 humidity sensor , light intensity , colour and gesture sensor ADPS-9960. There is also space for the MP34DT05 digital microphone. Additionally, onboard there was also a cryptographic system ATECC608A. Attention! Arduino Nano 33 BLE Sense can work ONLY with 3.3V by default. Do not supply it directly with 5 V. Arduino Nano 33 BLE Sense supports only 3.3 V by default. There is a jumper in place of the 5V pin in a standard Nano board (between RST and A7 pins) which can be shorted to the USB power supply. To supply 5V power to the devices, solder the jumper and power Nano via USB . If the jumper is soldered and no voltage is obtained from the V in pin. This is a protection to protect the Arduino Nano 33 BLE Sense. The board allows debugging programs, which is done with 6 pads on the bottom of the board underneath the communication system. The Arduino Nano 33 BLE Sense. Visible jumper for 5V power supply via USB. Pin Designation Type Description 1 D13 Digital GPIO 2 + 3V3 Power output Power supply for external devices 3 AREF Analogue Reference pin can be used as GPIO 4 A0 / DAC0 Analogue ADC input / DAC output can be used as GPIO 5 A1 Analogue ADC input can be used as GPIO 6 A2 Analogue ADC input can be used as GPIO 7 A3 Analogue ADC input can be used as GPIO 8 A4 / SDA Analogue ADC input, I2C SDA, can be used as GPIO* 9 A5 / SCL Analogue The ADC, I2C SCLinput can be used as GPIO*. 10 A6 Analogue ADC input can be used as GPIO 11 A7 Analogue ADC input can be used as GPIO 12 V USB I / Wy power supply Normally not connected. Can be shorted to USB power 13 RST Digital input Active reset 14 GND Power supply Mass 15 VIN Power supply Power supply 16 TX Digital USART TX can be used as GPIO 17 RX Digital USART RX can be used as GPIO 18 RST Digital Active reset 19 GND Power supply Mass 20 D2 Digital GPIO 21 D3 / PWM Digital GPIO can be used as GPIO 22 D4 Digital GPIO 23 D5 / PWM Digital GPIO can be used as GPIO 24 D6 / PWM Digital GPIO can be used as GPIO 25 D7 Digital GPIO 26 D8 Digital GPIO 27 D9 / PWM Digital GPIO can be used as GPIO 28 D10 / PWM Digital GPIO can be used as GPIO 29 D11 MOSI Digital SPI MOSI can be used as GPIO 30 D12 / MISO Digital SPI MISO can be used as GPIO (*) Unlike the standard Arduino Nano, the A4 and A5 pins have a default pull-up, the so-called pull-up and are used as I2C bus, so it is not recommended to use them as analogue inputs. Arduino Nano 33 BLE Sense PCB specification Supply voltage: 3.3 V Microcontroller: nRF 52840 Clock: 64 MHz Flash memory: 1 MB RAM 256 kB Digital pins: 14 PWM pins: 6 Analogue pins: 8 MicroUSB socket Interfaces: GPIO, SPI, I2C, USART, PWM Transducers: ADC, DAC Dimensions: 45 x 18 mm Useful links Manufacturer’s website Arduino Forum Installation and first start-up Arduino IDE software Documentation nRF 52840 LSM9DS1 documentation Documentation NINA B306 Documentation LPS22HB Documentation HTS221 ADPS-9960 documentation Documentation MP34DT05

From the supplier's page.