TMC2208 V1.2 Stepping Motor Mute Driver Stepstick Silent

TMC2208 Stepper Motor Driver Module MC2208 is an ultra-quiet two-phase stepper motor drive chip, continuous drive current 1.4A, peak current 2A, voltage range 4.75V-36V, 256 subdivision. The flexible microPlyer interpolation unit provides up to 256 subdivisions, allowing perfect sinusoidal control even in systems with limited pulse frequencies; these are also designed because stealthChop2 ultra-quiet technology is widely used in 3D printing. This product is known as 3D Printer TMC2208 Stepstick Stepper Motor Driver Module + Heat Sink, TMC2208 Stepper Motor Driver Module with Heat Sink for 3D Printer Part Features: Configuration: Step/DIR or UART Micro-steps: 1/256 Current Loading: 1.2A continuous, 2A peak Supply Voltage: 4.75 ~ 36V Single Wire UART: for advanced configuration options Features/Specs: Model: TMC2208 Interface: Step/Dir Configuration: CFG Pins or UART Native Micro steps: Up to 1/256 MicroPlyer Micro steps: 1/256 Logic Voltage VIO: 3 ~ 5V Motor Voltage VM: 5.5 ~ 36V Motor Phase Current: 1.2A RMS, 2.0A Peak Internal V-Regulator: Enabled Size (LxWxH) : 20 x 15 x 11 mm Note !!!: Make sure not to connect the motor when measuring voltage, otherwise driver will burn out. When used on Ramps1.4 or MKS Gen, please remove the 3 jumpers under socket. Pay attention to direction, don’t insert wrongly, or it will burnt out. The motor direction is opposite to that of A4988 and DRV8825, please adjust the firmware or adjust the motor wiring if you want to replace A4988. Package Includes: 1 x TMC2208 Stepper Motor Driver Module 1 × Heat Sink 1 × Screwdriver

The TMC2208 is an advanced and powerful stepper driver. It is mostly used in 3D printers’ driver motors with continuous drive current 1.2A, peak current 2A, voltage range 4.75V-36V. The TMC2208 stepper driver supports 256 micro steps (very smooth stepper motor motion) and also supports stealthChop mode of operation. StealthChop enable completely silences stepper motors by eliminating the noise caused by unsynchronized motor coil chopper operation, PWM jitter, and regulation noise. In addition, The TMC2208 has much better thermal dissipation and cooling performance which means more heavy duty and longer life of the driver The TMC2208 can be used as an upgrade of stepper driver such as A4988 or DRV8825 on Ramps style board or MKS GEN L board (this is called legacy mode). It can be used also in standalone mode or in UART mode where the stepper motor setting and tuning can be done through simple serial UART interface with your micro-controller. This make the TMC2208 driver flexible to use with any 3d printing board or technology without the need to redesign or make software or hardware changes. This TMC2208 stepper driver is provided with heat sink to protect the board from overheating. Features Configuration: Step/DIR or UART Micro-steps: 1/256 Current Loading: 1.2A continuous, 2A peak Supply Voltage: 4.75 : 36V Single Wire UART: for advanced configuration options TMC2208 datasheet Excellent intrsstuctable showing UART Serial Control of Stepper Motors With the TMC2208, Ramps 1.4 and Marlin TMC2208 Three way of control, part one: legacy mode TMC2208 Three way of control, part two: standalone mode TMC2208 Three way of control, part three: UART mode

TMC2208 V1.2 Stepper Motor Driver Module The TMC2208 is an advanced and powerful stepper driver. It is mostly used in 3D printers? driver motors with continuous drive current 1.2A, peak current 2A, voltage range 4.75V-36V. The TMC2208 stepper driver supports 256 micro steps (very smooth stepper motor motion). Specifications: Configuration: CFG or UART Microsteps: Up to 1/256 MicroPlyer: 1/256 Logic Voltage VI0: 3-5V Motor Voltage :?5.5-36V Motor Phase Current: 1.2A RMS, 2.0A Peak Package Includes: 1x TMC2208 Stepper Driver Module 1x Heatsink 1x Screwdriver Datasheet: TMC2208 Datasheet Related Products: MOTORS | DRIVERS