ST-LINK V2 Emulator and Debugger/Programmer for STM8 and STM32

ST-LINK V2 is a USB In-Circuit Programmer and Debugger for the STM8 and STM32 microcontroller families. The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontrollers. The single-wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board. In addition to providing the same functionalities as the ST-LINK/V2, the ST-LINK/V2-ISOL features digital isolation between the PC and the target application board. It also withstands voltages of up to 1000 V STM8 applications use the USB full-speed interface to communicate with the ST Visual Develop (STVD-STM8) or ST Visual Programmer (STVP-STM8) software, or with integrated development environments from third-parties. STM32 applications use the USB full-speed interface to communicate with the STM32CubeIDE software tool or with integrated development environments from third-parties. Features: Supporting the full range of STM32 SWD debugging interface Supporting the full range of STM8 SWIM download debugging (common development environments such as IAR The wiring is very simple because the interface definition is marked directly on the aluminum housing protects Internal board of this programmer is with 500MA self-recovery fuse It’s convenient and practical, fast speed and stable The interface easy to use simple horns seat pitch of 2.54 Flexible wiring Supporting for automatic firmware upgrades It can protect your computer motherboard 5 V power supplied by a USB connector USB 2.0 full-speed compatible interface Note: These USB sticks come in a variety of different colors. We’re unable to control the color you receive. The supported software versions are for example: ST-LINK Utility 2.0 and above STVD 4.2.1 and above STVP 3.2.3 and above IAR EWARM V6.20 and above IAR EWSTM8 V1.30 and above KEIL RVMDK V4.21 and above Package included: 1 x ST-LINK V2 Emulator Downloader Programmer Support STM8 STM32 1 x DuPont line

ST-Link V2 Programmer For STM8 and STM32 is fully consistent with the official version, support for automatic upgrades, support the full range STM32 SWD (only 4pins including SWCLK, SWDIO, and power) and a full range STM8 SWIM (only 4pins including SWIM, Reset and power) download and debug. Use this device to send program code to the 32-bit STM32 ARM Cortex or 8-bit STM8 microcontrollers. The header for this ST-Link v2 programmer contains connections for 5V, 3.3V, SWCLK, SWDIO, SWIM, Reset (RST/NRST) and GND. The connector on the opposite side of this device is a USB connector and is intended to be plugged into the computer. You can download the Drivers by clicking here Note: The product is available in Multiple colors Will be shipped randomly. Supports For ST-LINK V2 : ST-LINK Utility 2.0 and above. STVD 4.2.1 and above. STVP 3.2.3 and above. IAR EWARM V6.20 and above. IAR EWSTM8 V1.30 and above. KEIL RVMDK V4.21 and above. Features : PCB installed inside of aluminum alloy U disk shell , portable, safe and reliable! Interface definition directly marked on the shell, clear, convenient and practical! 5V, 3.3V offers at the same time, allowing you to program your target board with both 5V and 3.3V Shell characters using laser engraving, never fade off! Permanent clarity! 500MA internal resettable fuse, complete protection of your expensive computer motherboard! Red and blue color LED indicator , allowing you to always observe ST-LINK V2 working condition! With 4 DuPont line, so you can easily respond to different target board line order! Use anti-static bag packaging. SWIM specific features: SWIM cable for connection to the application via a pin header or a 2.54 mm pitch connector 1.65 V to 5.5 V application voltage supported on SWIM interface SWIM low-speed and high-speed modes supported SWIM programming speed rate: 9.7 Kbytes/s in low speed and 12.8 Kbytes/s in high speed SWIM cable for connection to the application Direct firmware update feature supported (DFU) Status LED which blinks during communication with the PC Operating temperature 0 to 50°C Package Includes ST Link V2 Programmer For STM8 and STM32 : 1 x ST-Link V2 Programmer For STM8 and STM32. 1 x Connecting Wires. Tutorials : Programming STM8 MCU Programmer For STM8 and STM32 Length (mm) 56 Width (mm) 20.5 Height (mm) 8.5 Weight (gm) 15 Shipment Weight 0.018 kg Shipment Dimensions 7 × 3 × 3 cm

ST-LINK V2 Emulator and Debugger/Programmer for STM8 and STM32 is a high-quality electronic component designed for Arduino, prototyping, and educational electronics. Supports full range of STM32 SWD 4-wire interface debug interface definition directly marked on the shell Supports full range of STM8 SWIM download debugging, supported software versions are as follows: Features: Official ST-LINK V2 design Supports STM32 and STM8 microcontrollers USB interface for easy connection Supports debugging & firmware upload Works with STM32CubeIDE, Keil, IAR, and more Fast, stable SWD/SWIM communication Includes wires/cables for connectivity Ideal for embedded development and testing