From Makers Electronics's description

Cytron MDD10A DC Motor Driver Dual Channel 10Amp 5V-30VDC The Cytron MDD10A is a dual-channel DC motor driver designed to control brushed DC motors. It is capable of handling up to 10A of continuous current per channel and a peak current of 30A for brief moments. The driver supports a motor voltage range from 5V to 30V (Rev2.0), making it suitable for a variety of robotic and motorized systems. Unlike older models, the MDD10A uses solid-state components that ensure faster response times and eliminate the wear and tear associated with mechanical relays, offering greater reliability and longevity. The MDD10A offers flexibility in motor control through its support for both sign-magnitude and locked-antiphase PWM signal operations. These modes allow the user to control the speed and direction of the motors easily. The driver supports TTL PWM inputs from microcontrollers, making it ideal for integration into custom robotics and automation projects. It also features onboard push buttons for manual motor control, providing additional convenience for testing and setup. The MDD10A is equipped with a variety of features for efficient operation, including full NMOS H-Bridge technology, which eliminates the need for a heat sink. It is designed to work with a battery for driving inductive loads like DC motors, as many power supplies shut down when regenerative currents are detected. The driver is compact yet powerful, making it a great choice for mobile robots, RC vehicles, and other applications that require precise motor control. Features: Bi-directional control for 2 brushed DC motors. Support motor voltage ranges from 5V to 25V 30V (Rev2.0). Maximum current up to 10A continuous and 30A peak (10 seconds) for each channel. Solid state components provide faster response time and eliminate the wear and tear of mechanical relay. Fully NMOS H-Bridge for better efficiency and no heat sink is required. Speed control PWM frequency up to 20KHz (Actual output frequency is same as input frequency). Support both locked-antiphase and sign-magnitude PWM operation. Support TTL PWM from microcontroller, not PWM from RC receiver. Onboard push button to control the motor manually. Dimension: 84.5mm x 62mm. Note: Please use the battery when driving inductive load such as DC brush motor. Due to the protection circuit of most power supply (switching), it will shut down when regenerative current from the motor is detected. Board Layout: 1. Red LED M1A: Turns on when the output M1A is high and output M1B is low. Indicates the current flows from output M1A to M1B. 2. Red LED M1B: Turns on when the output M1A is low and output M1B is high. Indicates the current flows from output M1B to M1A. 3. Green LED: Power LED. Should be on when the board is powered on. 4. Test Button M1B: When this button is pressed, current flows from output M1B to M1A and motor will turn CCW (or CW depending on the connection). 5. Test Button M1A: When this button is pressed, current flows from output M1A to M1B and motor will turn CW (or CCW depending on the connection). 6. Input: (that it is not for RC PWM) Pin No. Pin Name Description 1 GND Ground 2 *PWM2 PWM input for speed control (Motor 2) 3 DIR2 Direction input (Motor 2) 4 *PWM1 PWM input for speed control (Motor 1) 5 DIR1 Direction input (Motor 1) 7. Test Button M2A: When this button is pressed, current flows from output M2A to M2B and motor will turn CW (or CCW depending on the connection). 8. Test Button M2B: When this button is pressed, current flows from output M2B to M2A and motor will turn CCW (or CW depending on the connection). 9. Red LED M2B: Turns on when the output M2A is low and output M2B is high. Indicates the current flows from output M2B to M2A. 10. Red LED M2A: Turns on when the output M2A is high and output M2B is low. Indicates the current flows from output M2A to M2B. 11. Terminal Block: Connect to motor and power source. Pin No. Pin Name Description 1 Motor 1 Output B Connect to motor 1 terminal B 2 Motor 1 Output A Connect to motor 1 terminal A 3 POWER + Positive Supply (positive terminal of battery) 4 POWER – Negative Supply (negative terminal of battery) 5 Motor 2 Output A Connect to motor 2 terminal A 6 Motor 2 Output B Connect to motor 2 terminal B Specifications: Parameter Min Typical Max Unit Power Input Voltage: 5 – 30 V Maximum Continuous Motor Current: – – 10 A Peak Motor Current (10 seconds): – – 30 A Logic Input High Level (VIOH): 3 – 5.5 V Logic Input Low Level (VIOL): 0 – 0.5 V Maximum PWM Frequency: – – 20 kHz Dimension: Note: Please use battery when driving inductive load such as DC brush motor. Due to the protection circuit of most Power supply (switching), it will shut down when regenerative current from motor is detected. Even if the case where switching power supply is needed, a battery with the same rated voltage need to be parallel with the power supply to absorb the regenerative current. Applications: Robotic Applications. RC Vehicles. Motorized Systems. Differential Drive Robots. PWM Motor Control Systems. Automation Projects. Arduino Integrated Motor Control. Package Contents: 1x MDD10A Dual Channel 10A DC Motor Driver 1x 2510 PCB Connector – 5 Ways (Female) 5x 2510 Terminal Pin Documents: Datasheet: MDD10A User’s Manual Certificate: FCC Cert MDD10A CE Cert UKCA RoHS UKCA-EMC Cert 3D CAD: MDD10A Official Reseller: Makers Electronics

From Future Electronics Egypt's description

This is a dual motor MDD10A driver which is designed to drive 2 DC motor with high current up to 10A continuously and 30A peak. The driver works in voltage range from 5 to 25 V. It also includes fast test switch for driver testing. This driver supports locked-antiphase and sign-magnitude PWM signal. It uses full solid state components which result in faster response time and eliminate the wear and tear of the mechanical relay. Features Bi-directional control for 2 brushed DC motor. Support motor voltage ranges from 5V to 30V . Maximum current up to 10A continuous and 30A peak (10 second) for each channel. Solid state components provide faster response time and eliminate the wear and tear of mechanical relay. Fully NMOS H-Bridge for better efficiency and no heat sink is required. Speed control PWM frequency up to 20KHz. Support both locked-antiphase and sign-magnitude PWM operation. 2 activation buttons for fast test on each channel. Dimension: 84.5mm x 62mm For Dual DC motors 10A driver manual, click here Using MDD10A with Arduino

From Ampere Electronics's description

MDD10A Cytron 10Amp 5V-30V DC Motor Driver (2 Channels) DC brushed motor is the most commonly used and widely available motor in the market. Getting the motor to rotate is fairly easy, just connect the two terminals to power source and it will start spinning, that’s the beauty of DC brushed motor. Yet, if you want to control the speed, direction, activation and automate all these functions, check out this tutorial:? 5 easiest ways to control a DC motor . And using motor driver is one of the ways. MDD10A is one of Cytron’s motor driver series which offers easy to use features and it can drive two independent motors.