UNI-T UPO1104 Digital Oscilloscope 100MHz 4 Channel

UNI-T UPO1104 Digital Oscilloscope 100MHz 4 Channel The UNI-T UPO1104 is a 100 MHz, 4-channel digital phosphor oscilloscope designed to offer deep memory, high waveform capture rates, and real-time recording/playback with a 256-level grayscale display. It employs UNI-T’s Ultra Phosphor 2.0 technology, enabling clear visualization of transient events and fine waveform detail. With a maximum real-time sampling rate of 2 GSa/s (single channel) and a maximum memory depth of 56 Mpts, the UPO1104 can sustain high sampling rates across broad time-base settings while capturing up to 500,000 wfms/s in Fast Acquire mode. Hardware-based, uninterrupted waveform recording can store up to 120,000 frames for later review. Each of its four analog channels features low baseline noise (<100 μVrms), a vertical scale range from 500 μV/div to 20 V/div, and 8-bit resolution, optimized for precise signal observation. The integrated DVM module supports AC/DC TRMS measurements, and 36 automatic waveform‐parameter measurements can be performed within both screen and cursor‐selected areas. Rich triggering options (edge, pulse width, video, slope, runt, over‐amplitude, delay, timeout, duration, setup/hold, Nth-edge, code pattern) and full‐memory hardware decoding for RS232, I2C, and SPI facilitate complex signal analysis. Network and USB connectivity enable remote control, data storage, and SCPI programmability. Features: • Analog channel bandwidth: 100 MHz. • Four simultaneous analog channels. • Maximum real-time sampling rate: 2 GSa/s (single channel), 1 GSa/s (dual), 500 MSa/s (all four). • Vertical scale range: 500 μV/div to 20 V/div, 8-bit resolution, <100 μVrms noise. • Deep memory: 56 Mpts maximum per channel. • Waveform capture rate up to 500,000 wfms/s (Fast Acquire). • Hardware real-time waveform recording/playback up to 120,000 frames. • Automatic measurement of 36 parameters (screen and cursor areas). • Built-in DVM supporting AC/DC TRMS measurements (4½ digits). • FFT-based waveform math (add, subtract, multiply, divide, digital filter, logical/advanced operations) with 1 M-point FFT capability, waterfall display, demodulation, and marker measurement. • Multiple trigger types: edge, pulse width, video, slope, runt, over-amplitude, delay, timeout, duration, setup/hold, Nth-edge, code pattern. • RS232/UART, I2C, SPI hardware-based, real-time decoding. • Ultra phosphor display with 256-level grayscale on a 7″ WVGA (800×480) TFT LCD. • SCPI-compliant remote control via USB Device, USB Host, LAN, EXT Trig, and AUX Out (Trig Out, Pass/Fail, DVM). • Waveform navigation modes: time, marker, segment. • Pass/fail testing and SCPI programmability. • Web-server support for browser-based remote operation and data sharing. Specifications: Parameter: UPO1104 Specification Analog Bandwidth: 100 MHz Calculated Rise Time (10–90 %): ≤ 3.5 ns Channels (analog): 4 Maximum Sampling Rate: 2 GSa/s (single) 1 GSa/s (dual) 500 MSa/s (quad) Acquisition Modes: Normal, Peak Detect, High Resolution, Averaging (2–8192×) Maximum Memory Depth: 56 Mpts (all channels) Waveform Capture Rate: 150,000 wfms/s (Normal) 500,000 wfms/s (Fast Acquire) Hardware Real-Time Recording: 120,000 frames Display: 7″ WVGA (800×480) TFT LCD, 256-level grayscale, 24-bit true color, Point/Vector modes, persistence: Min, 50 ms–infinite, DSO Vertical System: Input Coupling: DC, AC, GND Input Impedance: 1 MΩ ± 2 % ∥ 16 pF ± 2 pF Probe Attenuation: 0.001X–2000X (user‐configurable) Max Input: 135 Vrms; 8-bit Vertical Scale: 500 μV/div to 20 V/div; Offset Range: 500 μV–50 mV/div: ±2 V 100 mV–500 mV/div: ±20 V 1 V–5 V/div: ±200 V 10 V–20 V/div: ±400 V Bandwidth Limit: 20 MHz Low-Frequency Response (AC, –3 dB): ≤ 5 Hz (on BNC) DC Gain Accuracy: < 10 mV: ±4 % FS; ≥ 10 mV: ±3 % FS DC Offset Accuracy: ±(2 % + 0.1 div + 2 mV) Channel-to-Channel Isolation: > 40 dB (DC to bandwidth) Horizontal System: Time Base Range: 1 ns/div–1000 s/div Time Base Accuracy: ±5 ppm initial, ±1 ppm/year Delay: Pre-trigger ≥ 1 screen, Post-trigger 1 s–50 s Modes: Y–T, X–Y, Roll Trigger System: Level Range: ±5 div (internal), EXT ± 9 V Modes: Auto, Normal, Single Coupling: DC, AC, HF Reject, LF Reject, Noise Reject Holdoff: 80 ns–10 s Types: Edge, Runt (> , <, ≤ ≥, None; Polarity +/–), Pulse Width (8 ns–10 s), Window (8 ns–10 s; Polarity +/–; Enter/Exit), Nth Edge (1–65,535; 8 ns–10 s Idle), Delay (8 ns–10 s; Edge type R/F; > , <, ≤ ≥, None), Timeout (8 ns–10 s), Pattern (H, L, X, Rising, Falling), Duration (8 ns–10 s; > , <, ≤ ≥), Setup & Hold (2 ns–4 s Setup; 8 ns–10 s Hold; Clock: R/F; Data: H, L), Pulse Slope (Polarity ±; > , <, < >; Time: 8 ns–1 s), Video (NTSC, PAL, SECAM) Decoding: RS232/UART (Baud: 2400–2,764,800 bps, custom; Data bits: 5–8), I2C (Start/Restart/Stop/Loss/Add/Data/ADDR; Addr mode: 7/10 bits; Addr range 0–127/0–1023; Byte length 1–5), SPI (Idle/Data/SS conditions; Timeout 80 ns–10 s; Data bits 4–32; Data set H, L, X; Clock R/F) Measurements: Cursors: ΔV, ΔT, 1/ΔT (Hz), Voltage/Time at point; Auto: 36 params (Max, Min, Top, Base, Amp, P-P, Middle, Avg, Avg-Cycle, RMS, RMS-Cycle, AC RMS, Period, Freq, Tr/Tf, RiseDelay, FallDelay, +Width, –Width, FRxR, FRxF, FxFR, FxFx, FRxL, FRxR, FLxR, FLxF, +Duty, –Duty, Area, Area-Cycle, Overshoot, Preshoot, Phase, Pulse count); Simultaneous: 5; Statistics: Mean, Max, Min, Std Dev, Count; Frequency Counter: 7-digit; XY: Time, Cartesian, Polar, Product, Ratio Math & FFT: A + B, A – B, A × B, A / B, FFT (Max 1 M points; Windows: Hanning, Hamming, Rectangle, Blackman, FlatTop; Display: Split, Full, Independent, Waterfall 1/2; Scale: Vrms, dBV; Spectrum Settings: Start, Stop, Center, Span; Detection: Normal, Avg, Max Hold, Min Hold; Marker: Type, Points, List), Editable: Log, Exp, Sin, Cos, Tan, Sqrt, Ln, floor, ABS, acos, asin, atan, sinh, tanh, ceil, cosh, fabs, intg, diff; Filters: LP, HP, BP, BS; Logic: AND, OR, NOT, XOR Storage & File: Internal: Inside/Outside External: USB (waveforms, settings, pictures) Probe Compensator Output: 3 Vpp; Frequency: 10 Hz, 100 Hz, 1 kHz, 10 kHz Interfaces: USB Host, USB Device, LAN, EXT Trig, AUX Out (Trig Out, Pass/Fail, DVM) Power: 100 – 240 VAC ± 10 % (50/60 Hz) or 100 – 120 VAC ± 10 % (400 Hz) 75 W max Fuse: 2.5 A, F-class, 250 V Environmental: Operating: 0 °C – 40 °C, ≤ 90 % RH (≤ 35 °C), Pollution Degree 2, Altitude < 3000 m; Non-operating: –20 °C – 70 °C, ≤ 60 % RH (35 °C–40 °C), Altitude < 15,000 m Dimensions & Weight: 336 mm × 170 mm × 110 mm 2.45 kg Safety & EMC: EN61010-1:2010 + A1:2019, EN61010-2-030:2021 + A11:2021, UL61010-1:2012 Ed.3+R:19 Jul 2019, UL61010-2-030:2018 Ed.2, CSA C22.2#61010-1:2012 Ed.3+U1/U2/A1, CSA C22.2#61010-2-030:2018 Ed.2; EMC: CISPR 11 Class B Group 1 (150 kHz–30 MHz & 30 MHz–1 GHz), ESD: IEC 61000-4-2 (4 kV contact, 8 kV air), EFT: IEC 61000-4-4 (2 kV), Surge: IEC 61000-4-5 (1 kV L–L, 2 kV L–G), RF Immunity: IEC 61000-4-3 (0 V/m 80 MHz–1 GHz, 3 V/m 1.4–2 GHz, 1 V/m 2–2.7 GHz), Conducted: IEC 61000-4-6 (3 V 0.15–80 MHz), Voltage Dips/Interrupts: IEC 61000-4-11 (0 % UT 1 cycle, 40 % UT 10/12 cycles, 70 % UT 25/30 cycles, Short 0 % UT 250/300 cycles) Calibration Interval: Recommended annually Applications: • Communication. • Semiconductor. • Computer. • IC Design. • Instrumentation. • Industrial Electronics. • Consumer Electronics. • Automotive Electronics. • Field Maintenance. • Research & Development / Education. Package Contents: • 1x Power cord that conforms to the destination country standard • 1x USB data cable (UT-D14) • 4x Passive probes (UT-P04, 100 MHz) • 1x Quick Start Guide • 1x Calibration Certificate • 1x CD with software, drivers, and manuals UNI-T UPO1104 Documents: • Datasheet • User Manual

With Serial bus trigger and hardware decoding (RS232, I²C, SPI, CAN, LIN)UNI-T Brand