From Micro Ohm's description

20A Range Current Sensor Module ACS712 The 20A Range Current Sensor Module ACS712 consists of a precise, low-offset, linear Hall circuit with a copper conduction path located near the surface of the die. Applied current flowing through this copper conduction path generates a magnetic field in which the Hall IC converts into a proportional voltage. Sensing and controlling current flow is a fundamental requirement in a wide variety of applications including, over-current protection circuits, battery chargers, switching mode power supplies, digital watt meters, programmable current sources, etc. This ACS721 current module is based on the ACS712 sensor, which can accurately detect AC or DC current. The maximum AC or DC that can be detected can reach 20A, and the present current signal can be read via analog I / O port of Arduino. Note: The color of the product may vary. while shipping you may get any one of them. We are supplying two more of such modules which equip ACS712 IC for current measurement, they are as below 5A Range Current Sensor Module ACS712 30A Range Current Sensor Module ACS712 Note: ACS712 is based on the Hall detection principle, please try to avoid the magnetic field, when using it as it may impact the reading accuracy. Features : The low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8 5.0 V, single-supply operation 66 to 185 mV/A output sensitivity Output voltage proportional to AC or DC currents Factory-trimmed for accuracy Extremely stable output offset voltage Nearly zero magnetic hysteresis The ratiometric output from the supply voltage. Package Includes : 1 x 20A Range Current Sensor Module ACS712 Useful Links: The Useful Introduction_1 from Embedded-lab. The Useful Introduction_2 from Embedded-lab. Current sensor chip ACS712ELC-20A Operating Voltage (V) 4.5V ~ 5.5V DC Measure Current Range -20 ~ 20A Sensitivity 100mV/A Length (mm) 32 Width (mm) 13 Height (mm) 13.5 Weight (gm) 5 Shipment Weight 0.01 kg Shipment Dimensions 7 × 3 × 3 cm

From Micro Ohm's description

The 30A Range Current Sensor Module ACS712 consists of a precise, low-offset, linear Hall circuit with a copper conduction path located near the surface of the die. Applied current flowing through this copper conduction path generates a magnetic field in which the Hall IC converts into a proportional voltage. Sensing and controlling current flow is a fundamental requirement in a wide variety of applications including, over-current protection circuits, battery chargers, switching mode power supplies, digital watt meters, programmable current sources, etc. This ACS721 current module is based on the ACS712 sensor, which can accurately detect AC or DC current. The maximum AC or DC that can be detected can reach 30A, and the present current signal can be read via analog I / O port of Arduino. Note: The color of the product may vary. while shipping you may get any one of them. We are supplying two more of such modules which equip ACS712 IC for current measurement, they are as below 5A Range Current Sensor Module ACS712 20A Range Current Sensor Module ACS712 Note: ACS712 is based on the Hall detection principle, please try to avoid the magnetic field, when using it as it may impact the reading accuracy. Features : The low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8 5.0 V, single-supply operation 66 to 185 mV/A output sensitivity Output voltage proportional to AC or DC currents Factory-trimmed for accuracy Extremely stable output offset voltage Nearly zero magnetic hysteresis The ratiometric output from the supply voltage. Package Includes : 1 x 30A Range Current Sensor Module ACS712 Useful Links: The Useful Introduction_1 from Embedded-lab. The Useful Introduction_2 from Embedded-lab. Current sensor chip ACS712ELC-30A Operating Voltage (V) 4.5V ~ 5.5V DC Measure Current Range -30 ~ 30A Sensitivity 100mV/A Length (mm) 32 Width (mm) 13 Height (mm) 13.5 Weight (gm) 5 Shipment Weight 0.01 kg Shipment Dimensions 7 × 3 × 3 cm

From Micro Ohm's description

5A Range Current Sensor Module ACS712 The 5A Range Current Sensor Module ACS712 consists of a precise, low-offset, linear Hall circuit with a copper conduction path located near the surface of the die. Applied current flowing through this copper conduction path generates a magnetic field in which the Hall IC converts into a proportional voltage. Sensing and controlling current flow is a fundamental requirement in a wide variety of applications including, over-current protection circuits, battery chargers, switching mode power supplies, digital watt meters, programmable current sources, etc. This ACS721 current module is based on the ACS712 sensor, which can accurately detect AC or DC current. The maximum AC or DC that can be detected can reach 5A, and the present current signal can be read via analog I / O port of Arduino. Note: The color of the product may vary. while shipping you may get any one of them. We are supplying two more of such modules which equip ACS712 IC for current measurement, they are as below 30A Range Current Sensor Module ACS712 20A Range Current Sensor Module ACS712 Note: ACS712 is based on the Hall detection principle, please try to avoid the magnetic field, when using it as it may impact the reading accuracy. Features : The low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8 5.0 V, single-supply operation 66 to 185 mV/A output sensitivity Output voltage proportional to AC or DC currents Factory-trimmed for accuracy Extremely stable output offset voltage Nearly zero magnetic hysteresis The ratiometric output from the supply voltage. Package Includes : 1 x 5A Range Current Sensor Module ACS712 Useful Links: The Useful Introduction_1 from Embedded-lab. The Useful Introduction_2 from Embedded-lab. Current sensor chip ACS712ELC-5A Operating Voltage (V) 4.5V ~ 5.5V DC Measure Current Range -5 ~ 5A Sensitivity 100mV/A Length (mm) 32 Width (mm) 13 Height (mm) 13.5 Weight (gm) 5 Shipment Weight 0.01 kg Shipment Dimensions 7 × 3 × 3 cm

From Makers Electronics's description

ACS712 Current Sensor Module 30A The ACS712 30A Current Sensor Module is a highly precise and economical solution for measuring both AC and DC currents. Based on the Hall Effect principle, this breakout board features a precise, low-offset, linear Hall circuit with an integrated copper conduction path. When current passes through the green screw terminal block, the onboard ACS712 chip detects the resulting magnetic field and converts it into a proportional, linear analog voltage output. Features Dual-Direction Sensing Onboard Power Indicator Easy Microcontroller Integration Compact Footprint Safe Terminal Blocks Specifications Parameter Specification Current Sensor Chip ACS712-30A Measurement Current 30A Operating Voltage (VCC) 5.0V DC (Nominal) Internal Conductor Resistance 1.2 mΩ (Typical) Module Dimensions 32mm × 14mm Applications Motor Control Circuits Electrical Load Management Switched-Mode Power Supplies (SMPS) Overcurrent Fault Protection DIY Robotics & Embedded Projects Package Content 1 x ACS712 Current Sensor Module 30A DataSheet ACS712

From Ampere Electronics's description

ACS712 Current Sensor Module – 20A The ACS712 is a fully integrated, hall effect-based linear current sensor with 2.1kVRMS voltage isolation and a integrated low-resistance current conductor. Technical terms aside, it?s simply put forth as a current sensor that uses its conductor to calculate and measure the amount of current applied. 80kHz bandwidth 66 to 185 mV/A output sensitivity Low-noise analog signal path Device bandwidth is set via the new FILTER pin 1.2 m? internal conductor resistance Total output error of 1.5% at TA = 25?C Stable output offset voltage. Near zero magnetic hysteresis applications: Motor speed control in motor control circuits Electrical load detection and management Switched-mode power supplies (SMPS) Protection for over-current 2D Model and Dimensions: Package Includes: 1x ACS712 module Product Datasheet: ACS712 Current Sensor Datasheet Related Products: Modules

From Ampere Electronics's description

ACS712 Current Sensor Module – 30A The ACS712 is a fully integrated, hall effect-based linear current sensor with 2.1kVRMS voltage isolation and a integrated low-resistance current conductor. Technical terms aside, it?s simply put forth as a current sensor that uses its conductor to calculate and measure the amount of current applied. 80kHz bandwidth 66 to 185 mV/A output sensitivity Low-noise analog signal path Device bandwidth is set via the new FILTER pin 1.2 m? internal conductor resistance Total output error of 1.5% at TA = 25?C Stable output offset voltage. Near zero magnetic hysteresis applications: Motor speed control in motor control circuits Electrical load detection and management Switched-mode power supplies (SMPS) Protection for over-current 2D Model and Dimensions: Package Includes: 1x ACS712 module Product Datasheet: ACS712 Current Sensor Datasheet Related Products: Modules

From Ampere Electronics's description

ACS712 Current Sensor Module – 5A The ACS712 is a fully integrated, hall effect-based linear current sensor with 2.1kVRMS voltage isolation and a integrated low-resistance current conductor. Technical terms aside, it?s simply put forth as a current sensor that uses its conductor to calculate and measure the amount of current applied. 80kHz bandwidth 66 to 185 mV/A output sensitivity Low-noise analog signal path Device bandwidth is set via the new FILTER pin 1.2 m? internal conductor resistance Total output error of 1.5% at TA = 25?C Stable output offset voltage. Near zero magnetic hysteresis applications: Motor speed control in motor control circuits Electrical load detection and management Switched-mode power supplies (SMPS) Protection for over-current 2D Model and Dimensions: Package Includes: 1x ACS712 module Product Datasheet: ACS712 Current Sensor Datasheet Related Products: Modules

From Makers Electronics's description

Current Sensor Module ACS712 5A The ACS712 Current Sensor Module is a compact, pre-assembled breakout board designed for direct current monitoring. The board centers around the ACS712 integrated circuit and features a clean, blue PCB layout with clearly labeled connection points, making it highly accessible for electronics projects and prototyping. Features Onboard Sensor Chip Easy Wiring Terminal Simple Interface Headers Visual Indicator Secure Mounting Specifications & Pinout Pin Label Description VCC Supply Voltage Input OUT Current Measurement Signal Output GND Ground Connection Applications Inline Current Sensing Analog Signal Processing Package Content 1 x Current Sensor Module ACS712 5A DataSheet ACS712