Heart Rate Monitor Kit with AD8232 ECG sensor Module

Heart Rate Monitor AD8232 The AD8232 Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as an analog reading. ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op amp to help obtain a clear signal from the PR and QT Intervals easily. The AD8232 is an integrated signal conditioning block for ECG and other biopotential measurement applications. It is designed to extract, amplify, and filter small biopotential signals in the presence of noisy conditions, such as those created by motion or remote electrode placement. The AD8232 Heart Rate Monitor breaks out nine connections from the IC that you can solder pins, wires, or other connectors to. SDN, LO+, LO-, OUTPUT, 3.3V, GND provide essential pins for operating this monitor with an Arduino or other development board. Also provided on this board are RA (Right Arm), LA (Left Arm), and RL (Right Leg) pins to attach and use your own custom sensors. Additionally, there is an LED indicator light that will pulsate to the rhythm of a heart beat. Biomedical Sensor Pads and Sensor Cable are required to use the heart monitor Note: This product is NOT a medical device and is not intended to be used as such or as an accessory to such nor diagnose or treat any conditions Pin Description of the AD8232 ECG Module Pin Name: Description GND: Power Supply Ground 3.3v: Power Supply 3.3v Output (ADC): Operational Amplifier Output. The fully conditioned heart rate signal is present at this output. OUT can be connected to the input of an ADC. LO-: Leads Off Comparator Output. In dc leads off detection mode, LO− is high when the electrode to −IN is disconnected, and it is low when connected LO+: Leads Off Comparator Output. In dc leads off detection mode, LOD+ is high when the +IN electrode is disconnected, and it is low when connected Shutdown Control Input. Drive SDN low to enter the low power shutdown mode. RA (Right Arm): RED Biomedical electrode pad RA(input). Instrumentation Amplifier Negative Input. −IN is typically connected to the right arm (RA) electrode LA (Left Arm): YELLOW Biomedical electrode pad LA(input). Instrumentation Amplifier Positive Input. +IN is typically connected to the left arm (LA) electrode RL(Right Leg): GREEN Biomedical electrode pad RL(input). Right Leg Drive Output. Connect the driven electrode (typically, right leg) to the RLD pin. 3.5mm ECG Biomedical Electrode Connector Jack: Combine Biomedical Electrode pad Connector of RA, LA, RL The pinout can be easily seen in the Board Legend. An example of the arrangement of the electrodes on the body. Features of the AD8232 ECG Module • Fully integrated single-lead ECG front end • Common-mode rejection ratio: 80 dB (dc to 60 Hz) • Two or three-electrode configurations • Qualified for automotive application • Single-supply operation: 2.0 V to 3.5 • Fast restore feature improves filter settling • Size: 3.5cm x 2.8cm Useful links • Datasheet (AD8232) • GitHub (Design Files & Example Code) Package Includes: • 1 x Ecg module AD8232 heart ECG monitoring sensor module. • Sensor Cable – Electrode Pads (3 Connector) • 3 x Electrode Pads.

Heart Rate Monitor Kit with AD8232 ECG sensor module The Heart Rate Monitor Kit with AD8232 ECG sensor module Kit For Arduino is a cost-effective board use to measure the electrical activity of the heart. This electrical activity can be chart as an ECG or Electrocardiogram and output as an analog reading. ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op-amp to help obtain a clear signal from the PR and QT Intervals easily. The ECG module AD8232 heart ECG monitoring sensor module is an integrated signal conditioning block for ECG and other bio-potential measurement applications. The ECG Module AD8232 Heart ECG Monitoring Sensor Module Kit for Arduino is designed to extract, amplify, and filter small bio-potential signals in the presence of noisy conditions; such as those created by motion or remote electrode placement. The AD8232 Heart Rate Monitor breaks out nine connections from the IC that you can solder pins, wires, or other connectors too. SDN, LO+, LO-, OUTPUT, 3.3V, GND provide essential pins for operating this monitor with an Arduino or other development board. Also provided on this board are RA (Right Arm), LA (Left Arm), and RL (Right Leg) pins to attach and use your own custom sensors. Additionally, there is an LED indicator light that will pulsate to the rhythm of a heartbeat. Biomedical Sensor Pads and Sensor Cable are required to use the heart monitor and can be found in the Recommended Products section. Pin Connections : Application Fitness and exercise heart rate monitoring Portable ECG Remote health care Gaming peripherals Biological signal acquisition Note: This product is NOT a medical device and is not intended to be used as such or as an accessory to such nor diagnose or treat any conditions. Features : Designed to extract, amplify, and filter small biopotential signals in the presence of noisy conditions, such as those created by motion or remote electrode placement. Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart. AD8232 is an integrated signal conditioning block for ECG and other biopotential measurement applications. ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op-amp to help obtain a clear signal from the PR and QT Intervals easily. This electrical activity can be charged as an ECG or Electrocardiogram and output as an analog reading. Leads-Off Detection. Shutdown Pin. LED Indicator. Analog Output. 3.5 mm Jack for Biomedical Pad Connection. Package Includes : 1 x Ecg module AD8232 heart ECG monitoring sensor module. 1 x Sensor cable. 3 x Electrode Pads. Operating Voltage (VDC) 3.3 Operating Temperature (°C) -40 to 90 Length (mm) 36 Width (mm) 30 Height (mm) 18 Weight (gm) 5 Cable Length (Meter) 1 Shipment Weight 0.01 kg Shipment Dimensions 10 × 8 × 2 cm

Electrocardiogram ECG Module AD8232 Heart Rate Monitor is a high-quality electronic component designed for Arduino, prototyping, and educational electronics. Ecg module AD8232 measurement pulse heart (ecg monitoring sensor) module kit. Product Description: The AD8232 is an integrated front-end for heart rate monitoring of signal conditioning of cardiac bio-electric signals. This is a low-power, single-lead heart rate monitor analog front-end for all types of vital signs monitoring applications. Product Parameters: Supply voltage: DC 3.3V Output Type: Analog Output Output Interface: 2.54 pin or headphone jack Product Size: 36mm * 31mm * 18mm Operating temperature: -40 degrees Celsius to +85 degrees Celsius Application: Fitness and sports heart rate monitoring Portable ECG Remote health monitor Game peripheral equipment Bio-electricity signal collection It’s perfect for DIY makers, students, and anyone building custom electronic circuits or STEM kits.